6110MR, Red-dot riser, 45 degree offset reflex, Right Hand

$65.99
SKU:
6110MR
Brand:

Tactical

  • Low Profile 45°
  • Right handed or right eye dominant shooters
Current Stock:
15
Adding to cart… The item has been added
Key Features:
Best Uses:

Description

Lightweight Aluminum
Picatinny interface
Designed and MADE IN USA

Specifically designed for right handed or right eye dominant shooters, Please see 6110ML for Left handed or left eye dominant shooters.

The Warne® 45° Offset Reflex Mount Is designed to offer a reflex sight mount that fits the most popular optic mounting patterns while seamlessly blending into the top rail of a rifle, ensuring the maximum amount of space to clear a scopes eyepiece or zoom ring. The height and angle of the mount place the optic in a position to allow for fast target acquisition.

With the increasing number of electro optics being used, finding a compatible mounting system can be confusing. We designed our modular Red Dot Riser to fit a wide range of different optics based on the mount footprint. All riser mounts that we offer share a robust mounting base, while the top is engineered specifically for different red dot styles. Fits:

  • Burris Fast Fire 2 & 3*
  • CMORE RTS & STS
  • Doctor
  • Eotech MRDS
  • Holosun 507c/407c V1 versions
  • Holosun 507c/407c V2 versions
  • Insight MRDS
  • Leupold Delta Point
  • Leupold Delta Point Pro
  • Shield RMS
  • Sig Romeo 3
  • Sig Romeo 3 Max
  • Sig Romeo 3 XL
  • Trijicon RMR
  • TrueGlo
  • UTG Reflex Micro Dot
  • Vortex Razor
  • Vortex Venom
  • Vortex Viper
  • And others with same hole pattern(s)
  • Designed and MADE IN USA

*Requires included hardware

Specifications

Part Number:
6110MR
Weight:
3.0 oz
Fits:
Burris Fast Fire 2 & 3, CMORE RTS & STS, Doctor, Eotech MRDS, Holosun 507c/407c V1, 507c/407c V2, Insight MRDS, Leupold Delta Point & Delta Point Pro, Shield RMS, Sig Romeo 3, 3 Max, 3 XL, Trijicon RMR, TrueGlo, UTG Reflex Micro Dot, Vortex Razor, Ve

Installation Instructions

Always verify that your firearm is UN-LOADED before performing any service on it. Warne recommends that you loosely assemble rings and scope onto firearm prior to final mounting to verify eye relief and ring spacing.
  • Identify the correct mounting holes using the included reversable alignment pins and install optic on the mount so the arrow is facing forward toward the muzzle end of the rifle (the included screws are intended for use with Doctor style mounting interface, other optics use the hardware included with the optic).
  • Install and torque optic to sight manufacturers recommended torque.
  • Remove the 2 T-15 torx screws and clamp from the mount and place the mount in the desired position on a rail (make sure that the mount or optic are not interfering with any portion of the scope or other accessories). The mount will not sit over the top of the rail but has 2 recoil lugs that blend seamlessly into the rail.
  • Install the clamp with the 2 T-15 screws and while putting pressure forward toward the muzzle tighten and torque the screws to 25 in-lbs max.
  • **Many scope manufacturers’ have established specific torque ratings for their scope and you must follow their recommended torque.

IMPORTANT: NEVER OVER TIGHTEN ANY BASE OR RING SCREW. NEVER ATTACH A SCOPE IF THE OBJECTIVE TOUCHES THE BARREL OR CAUSES INTERFERENCE WITH THE BOLT, SAFETY OR CYCLING OF THE ACTION. ALWAYS FOLLOW THE FIREARM OR SCOPE MANUFACTURERS’ RECOMMENDED TORQUE SPECIFICATIONS. YOU ARE RESPONSIBLE FOR YOUR OWN GUNSMITHING METHODS.

If you are unsure or do not have the proper tools, please contact a gunsmith for assistance, Warne will not be held liable for stripped/damaged receivers or scopes.